Orange Acres Welding Custom Built Trailers in Arlee

Orange Acres Welding Custom Built Trailers in Arlee 406 370-5466

Located behind OrangeMT.com Auto Sales IN ARLEE MT.

Wednesday, December 17, 2014

Raft winch and roller package, SEE VIDEO OF IT IN ACTION!!!!

available on any of our trailers for $250 up to 7 foot wide, $300 for 8 foot wide
to install one on your trailer we didnt build up to 7 foot wide, $350 on 8 foot wide.


see video of it here loading this raft

Monday, September 22, 2014

ADD A TILT TOUNGE TO OUR SINGLE AXLE TRAILERS FOR $200



<iframe width="420" height="315" src="//www.youtube.com/embed/HebG_9EKZ28" frameborder="0" allowfullscreen></iframe>

Saturday, March 8, 2014

80"x 10' foot Economy raft trailer $1550 or 1795 with winch roller and spare






above pictured with $250 optional winch and roller.








NEW Custom built raft trailers made right here in Montana


No one, builds a better, stronger trailer than us.

Full 80" inches wide x 10' foot long.

Made with 3/16ths thick 3inch channel steel, fully welded, 3" channel cross support on axle and gusseted. in front and rear,


These are a Tri Frame Tounge
3" tube tounge made of 3/16" inch steel, with a 2x3 A-frame supports on the tongue prevents tongue from breaking or bending when you hit something backing it up.

36" sub frame made from 3" channel ties into cross members (3'' inch channel) and welded to 5200 lb rated spring holders, with 3500lb springs.

optional Swing lock jack with a six inch wheel, you can lift this trailer by hand but if you have a bad back you will enjoy this jack for moving this trailer around. it swings sideways and sits lower than the deck so you could put a raft over the top of it if you had a 12 to 15' raft.

Due to problems that we have seen with 2000# axles, we only use a solid 3500 lb Dexter EZ lube axles, we use 3500# instead of 2000# axles because the have a bigger set of bearings than the 2000# axles so it means that they last longer. They also have a ez lube grease fitting on the hub for easy seasonal maintenance, you can put a grease gun on it or have the guys a jiffy lube do it for you. If you dont have EZ lube hubs you must remove the wheel and hub to pack the bearings. Incorrectly packing the bearings can cause the wheel to sieze resulting to tire blow out or the wheel falling off compleatly, rolling into oncomming traffic.

Full size 13" tires and wheels, trailer radials, not smaller 12'' or 8'' inch tires that turn faster and wear out bearings on highway. more ground clearance for getting over rocks and rolling over logs.
( I also sell them without tires and wheels if you want it cheaper or have tires yourself)

Custom 2 x 6 decking milled right here in Montana, stained with oil penetrating stain. Our deck boards fit in bolt down steel pockets for easy replacement in 20 years. Bolts don't go though decking( this causes decking to split over time due to flexing). also makes deck easy to remove for trailer painting or rhino lining in the future. (Also available undecked for discounted price, so if you want to install your own plywood that will rot out in a few years.)

2 coat of primer and 2-5coats Rustoleum brand Black paint, (also available unpainted if you have your own custom plans, rhino lining, truck color, or want to save a few bucks,)

this size, will also carry 2 ATV's sideways. Boxed in taillights, DOT stickers

OPTIONS AVAILABLE:

Raft package:
2'' full length roller bar, removable
sky winch and 20 ' strap, lifts rafts up as you winch it on trailer
spare tire mount in A-frame tongue.
tie down loop in rear center for locking down back of raft
10 steel stake pockets on sides and front for building side boards for enclosing or firewood racks.
plus 2 more stake pockets on tongue for strapping down ramps or securing front of raft.



also available in 5',6',80",7',and 8' widths
8'-20' lengths
call for pricing

Call Jeffrey-James at Orange Acres 370-5466 for more info.

Built by a Montana, who loves rivers and knows how rough Rock Creek and Blackfoot river roads can be.
Proud participant of the Blackfoot river cleanup.
Hit play button in botten left for video below!











video of our trailer after one year of use!
]
video of our trailer after one year of use!









Friday, March 7, 2014

7 x 12 raft trailers for floating and fishing the river, tilt models available

hand built custom trailers like the Amish, top quality welding and assembly, american made dexter ez lube axle and steel belted radial tires

7x12 with tri frame tilt tounge 15" tires and wheels , stake pockets, winch and roller bar



Saturday, January 25, 2014

8x12 snowmobile tilt trailer 15inch tires and wheels, winter price $1995





8x12 foot snowmobile atv raft trailer
tilt tounge raft atv snowmobile trailer , made in Montana, 3500 gvw  american made Dexter ez lube axle, 15" steel belted radial tires and wheels,
regular $2400 winter special $1995
fourosix threesevenofivefoursixsix
http://trailersorangemt.blogspot.com/

see youtube video of this trailer

Sunday, February 6, 2011

Our 7x12 Raft trailer $2200 cash WITH 15 INCH TIRES AND SPARE








NEW Custom built raft trailers made right here in Montana

THE BEST RAFT TRAILER YOU CAN BUY !!!!!

No one, builds a better, stronger trailer than this.

Full 7' foot wide (not 80" inches,) 12' foot long.

Made with 3/16ths thick 3inch channel steel, fully welded, 3" channel cross supports and gusseted.

Tri frame A-frame tongue prevents tongue from breaking or bending when you hit something backing it up.

8' sub frame made from 3" channel ties into 4 different cross members (3'' inch channel and angle) and welded to 5200 lb rated spring holders, with 3500lb springs.
8" wheel jack or Optional Drop foot jack, pull pin and let it fall to ground then start turning it, no need for block under jack. This jack is triple support welded, with grease zerk, set back 24" from front so you can still open your tailgate . I put these jacks on our 7000 gvw trailers also. it is not going to bend sideways when you drop the trailer with a load on it.

Due to problems that we have seen with 2000# axles, we only use a solid 3500 lb Dexter EZ lube axles, we use 3500# instead of 2000# axles because the have a bigger set of bearings than the 2000# axles so it means that they last longer. they also have a ez lube grease fitting on the hub for seasonal maintenance.

Full size 15" tires and wheels, 205 trailer radials, with spare, not smaller tires that turn faster and wear out bearings on highway. more ground clearance for getting over rocks and rolling over logs.
( I also sell them without tires and wheels if you want it cheaper or have tires yourself)

Custom 2.5 x 6.5 decking milled right here in Montana, extra thick, stained with oil penetrating stain. Our deck boards fit in bolt down steel pockets for easy replacement in 20 years. Bolts don't go though decking( this causes decking to split over time due to flexing). also makes deck easy to remove for trailer painting or rhino lining in the future. (Also available undecked for discounted price, so if you want to install your own plywood that will rot out in a few years.)

2 coat of primer and 2-5coats Rustoleum brand Black paint, (also available unpainted if you have your own custom plans, rhino lining, truck color, or want to save a few bucks,)

Raft package:
2'' full length roller bar, removable
sky winch and 20 ' strap, lifts rafts up as you winch it on trailer
spare tire mount in A-frame tongue.
tie down loop in rear center for locking down back of raft
10 steel stake pockets on sides and front for building side boards for enclosing or firewood racks.
plus 2 more stake pockets on tongue for strapping down ramps or securing front of raft.

I recommend this size, it holds a 12' -14' foot raft, or a 10' foot raft and a toolbox, it will also carry 3 ATV's sideways.

available in 5',6',80",7',and 8' widths
8'-20' lengths
call for pricing

Call Jeffrey-James at Orange Acres 370-5466 for more info.

Built by a Montana, who loves rivers and knows how rough Rock Creek and Blackfoot river roads can be.
Proud participant of the Blackfoot river cleanup.

Wednesday, December 1, 2010

new car dollys 1195$


Stehl Tow Features

Features:

The Stehl Tow Model ST80TD will haul small, medium and large cars, trucks and vans.

We use E/Z Lube Hubs, eliminating the need for disassembly of the wheel bearing for repacking.


Our fenders are steel with 3 steel support braces.

We use a factory molded, plug together wiring harness.

We use a powder-coated paint that is the most durable finish on the market. This paint is second to none and keeps your dolly looking good long after you buy it.

All of our dollies come with a 1-year factory warranty*. A warranty card is included with the owner’s manual provided with each dolly.



*1-Year Warranty Card excludes tow dollies used for repossession, these have a limited 90-day warranty.

Tuesday, June 1, 2010

7x12 flatbed raft atv with no winch or roller $1995 cash price




heavy duty commercial grade trailers built for rough roads with premuim dexter ez lube axles.

in stock ready for delivery today!!!!!!!!!!

Also great for ATVs (fits 3 sideways), snowmobiles, construction materials, and fire wood and wood pellets, has stake pockets so you can build side racks.

cash price $1695 .

THE BEST RAFT TRAILER YOU CAN BUY !!!!!


No one, builds a better, stronger trailer than this.


Full 7' foot wide (not 80" inches,) 12' foot long.


Made with 3/8ths thick 3inch channel steel, fully welded, 3" channel cross supports and gusseted.


3" tube 3/16" thick with 3x2 a-frame supported tongue prevents tongue from breaking or bending when you hit something backing it up.


8' sub frame made from 3" channel ties into cross members (3'' inch channel) and welded to 5200 lb rated spring holders, with 3500lb springs.


Drop foot jack, pull pin and let it fall to ground then start turning it, no need for block under jack. This jack is triple support welded, with grease zerk, set back 20" from front so you can still open your tailgate . I put these jacks on our 7000 gvw trailers also. it is not going to bend sideways when you drop the trailer with a load on it.


Due to problems that we have seen with 2000# axles, we only use a solid 3500 lb Dexter EZ lube axles, we use 3500# instead of 2000# axles because the have a bigger set of bearings than the 2000# axles so it means that they last longer. they also have a ez lube grease fitting on the hub for seasonal maintenance.


Full size 15" tires and wheels, 205 trailer radials, not smaller tires that turn faster and wear out bearings on highway. more ground clearance for getting over rocks and rolling over logs.
( I also sell them without tires and wheels if you want it cheaper or have tires yourself)


Custom 2 x 6.5 and 2x8 decking milled right here in Montana, extra thick, stained with oil penetrating stain. Our deck boards fit in bolt down steel pockets for easy replacement in 20 years. Bolts don't go though decking( this causes decking to split over time due to flexing). also makes deck easy to remove for trailer painting or rhino lining in the future. (Also available undecked for discounted price, so if you want to install your own plywood that will rot out in a few years, or cough up big money and install trex decking)


2 coat of primer and 2-5coats Rustoleum brand Black paint, (also available unpainted if you have your own custom plans, rhino lining, truck color, or want to save a few bucks,)

tie down loop in rear center for locking down back of raft or atvs
10 steel stake pockets on sides and front for building side boards for enclosing or firewood racks.
plus 2 more stake pockets on tongue for strapping down ramps or securing front of raft.
I recommend this size, it holds a 12' -14' foot raft, or a 10' foot raft and a toolbox, it will also carry 3 ATV's sideways.

Friday, February 5, 2010

8x10 tilt snowmobile atv or raft trailer 1795$ cash

$200 discount when you order one of these in November December and January.



8x10 tilt snowmobile atv or raft trailer

hole in center of deck for ratchet straps for skis

heavy duty commercial grade trailers built for rough roads with premuim dexter ez lube axles.

in stock ready for delivery today!!!!!!!!!!

Also great for ATVs , snowmobiles, construction materials, and fire wood and wood pellets, has stake pockets so you can build side racks.

cash price $1495,

THE BEST snowmobile TRAILER YOU CAN BUY !!!!!


No one, builds a better, stronger trailer than this.


Full 8' foot wide also available in 12' foot long.


Made with 3/8ths thick 3inch channel steel, fully welded, 3" channel cross supports and gusseted.


3" tube 3/16" thick with 3x2 a-frame supported tongue prevents tongue from breaking or bending when you hit something backing it up.


8' sub frame made from 3" channel ties into cross members (3'' inch channel) and welded to 5200 lb rated spring holders, with 3500lb springs.


swing lock jack with roller wheel set back 20" from front so you can still open your tailgate . I put these jacks on our 7000 gvw trailers also.


Due to problems that we have seen with 2000# axles, we only use a solid 3500 lb Dexter EZ lube axles, we use 3500# instead of 2000# axles because the have a bigger set of bearings than the 2000# axles so it means that they last longer. they also have a ez lube grease fitting on the hub for seasonal maintenance.


Full size 13" tires and wheels, trailer radials, not smaller 8' tires that turn faster and wear out bearings on highway. more ground clearance for getting over rocks and rolling over logs.
( I also sell them without tires and wheels if you want it cheaper or have tires yourself) also available with 15" wheels and tires


Custom 2 x 6.decking milled right here in Montana, stained with oil penetrating stain. Our deck boards fit in bolt down steel pockets for easy replacement in 20 years. Bolts don't go though decking( this causes decking to split over time due to flexing). also makes deck easy to remove for trailer painting or rhino lining in the future. (Also available undecked for discounted price, so if you want to install your own plywood that will rot out in a few years, or cough up big money and install trex decking)


2 coat of primer and 2-5coats Rustoleum brand Black paint, (also available unpainted if you have your own custom plans, rhino lining, truck color, or want to save a few bucks,)

tie down loop in rear center for locking down back of raft or atvs
10 steel stake pockets on sides and front for building side boards for enclosing or firewood racks.
plus 2 more stake pockets on tongue for strapping down ramps or securing front of raft.
I recommend this size, it holds a 12' -14' foot raft, or a 10' foot raft and a toolbox, it will also carry 2 ATV's.

video below is optional  12' legnths and 15"tires

Wednesday, January 20, 2010

Deck over wheels Raft Trailer for sale












here is an example of one of our deck over wheels raft trailers,

they feature a 3500 lb dexter ez lube axle, we use 3500# instead of 2000# axles because the have a bigger set of berrings than the 2000# axles that last longer. they also have a ez lube grease fitting

2x6 decking milled right here in montana

our deck boards fit in bolt down steel pockets for eazy replacement. bolts don't go though decking( this causes decking to split over time due to flexing).

3" channel frame and aframe tounge

available with:
roller bar
sky winch
spare tire mount
tie down loops
stake pockets
tool box mounts
13" or 15" tires and wheels
tounge jack, dropfoot jack, or swing lock jack

available in 6'-8' widths
8'-14' legnths
call for pricing 370-5466

Saturday, November 14, 2009

Car hauler utility duel axle trailers.







80" wide deck, about 82" inbetween fenders



16' $2195 without wheels and tires , $2595 with new 15" tires and rims (save $200 when buying a trailer)


18' add $100 or 20' add $200








Here are some pictures of our Deck between Duel axel trailers, these can be customized by us for you and used for hauling, vehicles, tractors and equipment, rafts, atvs, motorcycles, 4wheelers, golf carts, firewood, landscape and contracter work trailers.


These trailers come with:

-heavy duty dropfoot jack with greese zerk,
-2' or 2 5/16'' coupler

- brakes on one axle,
-3500# dexter ez lube axles
-14'' or 15'' or tires and wheels
-D.O.T lighting with boxed in tailight protectors

-treadplate fenders with 3"channel supports

-bang board
- fir deck from Tri-Con lumber milled in St.Regis Montana.
-Made in Missoula County Montana

-5 inch channel frame, 4" channel tounge.
-16 stake pockets

Options include:

-Brakes on 2 axles instead of 1 add $150
-5200# axles and 6000# axles
-Drop axels
-Bulldog hitch
-Side utility Rails
-Raft winch or Utility winch and Rear raft rollers
-Toolbox and gear carriers
-Spare tire and mount
-screw down, dropfoot and swing lock jacks with dropfoot or swivel wheel
-8' width extenions for side by side 4wheelers
-Stake pockets, tie down hooks
-ramps, rampcarriers, ramp bars

-Order trailer today and recive our 5' ramps made from 3" channel, Normally $250, for $150 more

80.5"x12' deck between Channel A-Frame












optional side ramp bars

Starting at $1595.
tri-frame tounge
stakepockets on all four sides and tounge for enclosing and securing load
dropfoot jack
3" channel frame and tri frame 3/16" thick tounge, stronger than our compeditors
2 inch coupler
tailight protectors
dot stickers and lighting
diamond plate fenders
2x6 fir deck stained
side ramp bars
6 hole isuzu wheels and 15 ich tires
3500lb gvw dexter ez lube axle

great for raft atv, or build side racks and gate for moving and firewood



Trailer raft atv



"Here are some pictures of our Deck under single axle trailers, these can be customized by us for you and used for hauling, rafts, atvs, motorcycles, 4wheelers, golf carts, firewood, landscape and contracter work trailers.

These trailers come with:

-3500# axle
-14' or 15' tires and wheels
-D.O.T lighting
-Rough cut fir deck for Tri cut lumber in St.Regis
-Made in Missoula Montana
-safty chains
-2'' coupler
- Available in 5', 6', 6.5', and 7' widths and 8',10', and 12 foot lenths.

Options include:
_tilt tounge
-lube eazy axle hubs
-Raft winch and Rear rollers
-Toolbox and gear carriers
-Spare tire and mount
-swing lock jacks with dropfoot or swivel wheel
-Fruit rollup dispencer
-8' width extenions for side by side 4wheelers
-Stake pockets, tie down hooks
-ramps, rampcarriers, ramp bars"